J&S Valve combines the highest quality materials available in an AWWA Gate Valves, C500, C509 & C515 Resilient Seated & Solid Wedge Metal Seated Gate Valve, Commercial Butterfly Valves, Duckbill Check Valve, and WaStop
Check Valves.
J&S Gate Valves –Resilient Seated & Solid Wedge Metal Seated
J&S Gate Valves offer Ductile Iron Body, Bonnet, Wedge and Gland whereas the AWWA Specifications allow for Cast Iron. Cast Iron (Class B) has approximately 1% elongation verses ductile iron which has approximately 9% elongation. The tensile strength of Cast Iron is 31,000 psi.
|
 |
|
The tensile strength of Ductile Iron is 65,000psi. Since Cast Iron
has less elongation than Ductile Iron, it can rupture under less
pressure than Ductile Iron. When pressure surges occur in a system,
Ductile Iron Valves can withstand higher pressure surges than Cast Iron
Valves. The Ductile Iron Wedge is totally encapsulated with EPDM Rubber
verses Buna-N. EPDM is more resistant to Chlorine and Chloramines which are used in high concentration in Reuse Water Systems. J&S standardizes on Stainless Steel Stem that has a tensile strength of 64,000psi which is twice as much as Bronze Stems.
This selection of materials along with Stainless Steel Fasteners and
NSF/ANSI 61 Approved Fusion Bonded Epoxy coating* on the interior of the valves, the exterior of the valves and on the hand wheel or 2" operating nuts assures the End-User a robust, long lasting, maintenance free valve.
J&S Valve is the Most Complete Line of AWWA Gate Valves in America.
 |
AWWA Resilient Seated Gate Valves: J&S Valve Flange by Flange, NRS, Series 6800 Sizes 2”- 96”
J&S Valves Improve the Industry Standard for AWWA Gate Valves by Manufacturing a Heavy Thick Wall All Ductile Iron Gate Valve with a Large Diameter Stainless Steel Stem, Stainless Steel Hardware, and a Superior Interior and Exterior Fusion Bonded Epoxy Coating. The J&S Robust Design Resists Breaking Stems and Valve Damage. |
 |
AWWA Resilient Seated Valves: AWWA Flange by Mechanical Joint, NRS, Series 6600 Sizes 2” - 48”
J&S Valves Improve the Industry Standard for AWWA Gate Valves by Manufacturing a Heavy Thick Wall All Ductile Iron Gate Valve with a Large Diameter Stainless Steel Stem, Stainless Steel Hardware, and a Superior Interior and Exterior Fusion Bonded Epoxy Coating. The J&S Robust Design Resists Breaking Stems and Valve Damage. |
 |
AWWA Resilient Seated Valves: AWWA Mechanical Joint by Mechanical Joint, NRS, Series 6900
Sizes 2” - 48”
J&S Valves Improve the Industry Standard for AWWA Gate Valves by Manufacturing a Heavy Thick Wall All Ductile Iron Gate Valve with a Large Diameter Stainless Steel Stem, Stainless Steel Hardware, and a Superior Interior and Exterior Fusion Bonded Epoxy Coating. The J&S Robust Design Resists Breaking Stems and Valve Damage. |
|
FL X FL, NRS Resilient Seated Sizes: 2” - 96 ” Series 6800 |
FL X MJ, NRS
Resilient Seated
Sizes: 2” - 48 ”
Series 6600 |
MJ X MJ, NRS
Resilient Seated
Sizes: 2” - 48”
Series 6900 |
 |
AWWA Resilient Seated Valves: AWWA Flange by Flange, OS&Y, Series 6700
Sizes 2” - 54”
J&S Valves Improve the Industry Standard for AWWA Gate Valves by Manufacturing a Heavy Thick Wall All Ductile Iron Gate Valve with a Large Diameter Stainless Steel Stem, Stainless Steel Hardware, and a Superior Interior and Exterior Fusion Bonded Epoxy Coating. The J&S Robust Design Resists Breaking Stems and Valve Damage. |
 |
AWWA Resilient Seated Valves: AWWA Push On by Push On, NRS, Series 6500
Sizes 4” - 12”
the most robust gate valve on the market. Push On end connections for use with Ductile Iron and C900 PVC Pipe. J&S Valves Improve the Industry Standard for AWWA Gate Valves by Manufacturing a Heavy Thick Wall All Ductile Iron Gate Valve with a Large Diameter Stainless Steel Stem, Stainless Steel Hardware, and a Superior Interior and Exterior Fusion Bonded Epoxy Coating. The J&S Robust Design Resists Breaking Stems and Valve Damage. |
 |
AWWA Resilient Seated Valves: AWWA Flange by Push On, NRS, Series 6400, Sizes 4” - 12”
the most robust gate valve on the market. Flanges conform to ANIS B16.1, Class 150, Push On end connections for use with Ductile Iron Pipe and C900 PVC Pipe. J&S Valves Improve the Industry Standard for AWWA Gate Valves by Manufacturing a Heavy Thick Wall All Ductile Iron Gate Valve with a Large Diameter Stainless Steel Stem, Stainless Steel Hardware, and a Superior Interior and Exterior Fusion Bonded Epoxy Coating. The J&S Robust Design Resists Breaking Stems and Valve Damage. |
FL X FL, OS&Y
Resilient Seated
Sizes: 2” -54”
Series 6700 |
PO X PO, NRS
Resilient Seated
Sizes: 4” - 12”
Series 6500 |
FL X PO, NRS
Resilient Seated
Sizes: 4” - 12”
Series 6400 |
WaStop Valves
WaStop® inline check valves are designed to operate in several installation alternatives. The check valve can be attached with flanges, angle irons, slide muffs or joint couplings. Installation can be at inlet or outlet, inside existing pipe, between existing pipes, or in a manhole. The inline check valve allows flow in one direction only.
 |
WaStop® Inline Check Valves Stainless Steel Body:
WaStop Inline Check Valves Stainless Steel Body Sizes 4”-70”
WaStop® inline check valves are designed to operate in several installation alternatives. The check valve can be attached with flanges, angle irons, slide muffs or joint couplings. Installation can be at inlet or outlet, inside existing pipe, between existing pipes, or in a manhole. The inline check valve allows flow in one direction only. |
 |
WaStop® Inline Check Valves PVC Body:
WaStop Inline Check Valves PVC Body Sizes 3”-12”
WaStop® inline check valves are designed to operate in several installation alternatives. The check valve can be attached with flanges, angle irons, slide muffs or joint couplings. installation can be at inlet or outlet, inside existing pipe, between existing pipes, or in a manhole. The inline check valve allows flow in one direction only. |
|
WaStop® Inline Check Valves PE Body:
WaStop Inline Check Valve PE BodySizes 40”-70”
WaStop® inline check valves are designed to operate in several installation
alternatives. The check valve can be attached with flanges, angle irons, slide muffs or joint couplings. installation can be at inlet or outlet, inside existing pipe, between existing pipes, or in a manhole. The inline check valve allows flow in one direction only. |
WaStop Inline Check Valves Stainless Steel Body Sizes 4”-70” |
WaStop Inline Check Valves PVC Body Sizes 3”-12” |
WaStop Inline Check Valves PE Body Sizes 40”-70” |
Commercial Butterfly Valves
J & S Valve combines the highest quality materials in our General Purpose Commercial Butterfly Valves. We offers the body made of cast iron, the disc of 316 stainless steel, the shaft of 304 stainless steel and the seat is EPDM for service temperatures up to 250°F. We offer the General Purpose Commercial Butterfly Valves in both wafer style and lug style bodies. We offer 2" - 12" Lever Operated and 5" - 24" we offer with a gear operator.
 |
Wafer Style Commercial Butterfly Valve Series 2300
Sizes 2” - 24”
General Purpose Commercial Wafer Body Style Butterfly Valves fit between ANSI Class 125 or Class 250 Flanges. Valve Body shall be cast grey iron ASTM 126 Grade B. Valve stem are be 304 stainless steel . The disc material is 316 stainless steel. The seat material is EPDM. The stem seals o-rings are made of EPDM. Valves 2” - 8” are lever operated and valves 10” and larger can be gear operated unless automatic operation is preferred. Wafer Style Butterfly Valve are suitable for air service for temperature up to 250°F. Wafer Body Butterfly Series 2300 Manufactured by J&S Valve and Manufacturing, Huffman, Texas. |
 |
Lug Style Commercial Butterfly Valves
Sizes 2” - 24”
General Purpose Commercial Butterfly Valves Lug Body Style for dead end service be bolted to ANSI Class 125 or Class 250 Flanges. Valve Body are cast grey iron ASTM 126 Grade B. Valve stem are 304 stainless steel . The disc material is 316 stainless steel. The seat material is EPDM. The stem seals is rubber o-rings made of EPDM. Valves 2” - 8” have lever operated and valves 10” and larger are gear operated unless automatic operation is specified. Valve are suitable for air service for temperature up to 250°F. Lug Body Butterfly Series 2500 are Manufactured by J&S Valve and Manufacturing, Huffman, Texas. |
Wafer Style Commercial Butterfly Valve Sizes: 2”-24” Series 2300 |
Wafer Style Commercial Butterfly Valve Sizes: 2”-24” Series 2500 |
HedFlex Duckbill Valves
J&S HedFlex Check Valves are constructed with superior high grade rubber and superior polyester reinforcement to improve performance, operation, and life expectancy. There are many grades of rubber that vary in chemical make-up. The elastomer’s chemical make-up “the recipe“ determines cost, characteristics, durometer (hardness and stiffness), and quality of the rubber parts used to construct HedFlex Check Valves.
 |
J&S HedFlex Duckbill Check Valve Sizes 1”-96” Series DBV-09FL
Model DBV-09-FL is designed to bolt to flanges. J&S HedFlex Check Valves are constructed with superior high grade rubber and superior polyester reinforcement to improve performance, operation, and life expectancy. There are many grades of rubber that vary in chemical make-up. The elastomer’s chemical make-up “the recipe“ determines cost, characteristics, durometer (hardness and stiffness), and quality of the rubber parts used to construct HedFlex Check Valves. |
 |
J&S HedFlex Duckbill Check Valve Sizes 1”-96” Series DBV-09SO
Model DBV-09-SO is designed to slip over the pipe and secured with stainless steel clamps.J&S HedFlex Check Valves are constructed with superior high grade rubber and superior polyester reinforcement to improve performance, operation, and life expectancy. There are many grades of rubber that vary in chemical make-up. The elastomer’s chemical make-up “the recipe“ determines cost, characteristics, durometer (hardness and stiffness), and quality of the rubber parts used to construct HedFlex Check Valves. |
HedFlex Duckbill Check Valve Model DBV-09FL Sizes:1”-96” |
HedFlex Duckbill Check Valve Model DBV-09-SO Sizes:1”-96” |
|
